Showing posts with label lathe. Show all posts
Showing posts with label lathe. Show all posts

Saturday, 30 March 2013

DIY Sping Compressor


                                             

                                          

 In the past if i ever needed to compress a spring for one of my air rifles i would use the wood lathe, it was one of those jobs where you would clamp a drill in the headstock. The tailstock would adjust by sliding along a round bar then lock in place, it had a live centre which would wind in about four inches. By placing a wooden bed above the round bar and a block of wood over the hole for the drill in the headstock, i could then secure the spring and piston cylinder to the bed at the right height for it to be in line with the centre on the head stock. This worked fine unless there was a lot of preload on the spring but i usually found some way around that. However i had other plans for the wood lathe, and that was to convert it to a rudimentary metal lathe which i did. Unfortunately the conversion made it impractical to use it as a spring compressor anymore, and besides i really needed a bit more than four inches of movement when taking a spring out.



Makeshift metal lathe from old wood lathe



Having seen other DIY spring compressors on you tube and various airgun websites i decided i would have a go myself, and the sooner i did it the sooner i could get on with tuning up the glut of air rifles i was given. Not only that but its bloody freezing in the shed sometimes, and it would be a lot warmer to work on the kitchen table with some thing a little bit more portable with easier access to to the kettle


.
Cylinder bed
Framework for nuts and threaded bar





There was a load of various offcuts of wood in the shed, and instead of using an old G clamp i would use some 12mm threaded bar and nuts surrounded by a plywood frame and secured with metal putty. An old piece of wooden shelf was used for the base, the end block was very hard wood in which i cut a slot in for barrels to fit through. This was butted against three lengths of wood that ran part length up the base, the middle piece being a tad lower so an air rifle cylinder would sit comfortably.

Threaded bar clamped for cutting

Handy homemade disc cutter attachment for the drill


Bar lined up, washers and nuts in place for metal putty to be packed in



As the most pressure is pushed outwards against the two end blocks i decided i would strenthen and support them with metal brackets bolted to the bed, i then made a trough for a piece of hardwood to slide without slipping when the threaded bar is wound against the back of the rifle. When i tuned the Norica Quick the cylinder was held in place with strong tape, though later i drilled two holes in the bed and popped a couple of coach bolts through them. Now i could clamp a piece of wood strengthened by aluminium to act as a clamp.


Nuts held tight, metal bracket for extra support
Plastic strip for support trough

Admittedly it did not like the five inches of preload from the Norica's mainspring, but after a little settling in it did the job fine. This one will do for now but i have a load of metal frame and sqare section that will make a more permanent compressor, and this one should be able to handle a lot more pressure. But the odd jobs keep mounting and there is no telling when that will get done, let alone the tuning of my other springers and the Weihrauch HW35 most definitely needs a good check up as it's not as accurate as it used to be.


Just needs a few finishing touches

Thursday, 29 November 2012

The workshed and the art of trying to complete one project at a time.

The stuff you can learn on you tube nowadays is amazing. I wanted a forge to cast aluminium and thanks to a blog by 'MYFORDBOY' I was able to make just that. I needed a simple metal lathe and with a bit of googling i'm well on my way to coming up with something well useable though not precision made, but the tolerances are fine for now. With what I have now i could buid a very fine 'gingery lathe'. 'THE VINTAGE PROJECT' and 'THE BACKYARD  METAL CASTING BLOG' are perfect for this.

So now down to my air rifles. There's the 22 Wiehrauch hw 35 which only needs an inspection and a lube really, seeing as its shooting one inch groups at 30 yards and the woodwork is uttererly unique with immaculate blueing.



I bought two Crosmans a while back. The pistol, a 2044, is one the best pistols you can get for your money. It comes with many after market parts. The other is the Air Source 1077 which is a repeater based upon the Ruger 1022 firearm, this little beaut is hours of fun but can be exspensive in co2 depending on how carried away you get with it, and with it being a cold November morning the power drops like Shelley Winters off a cliff edge. I did have an idea once to change the barrels in the 1077 from a 177 to a 22, but we shall wait and see on that one, shall we?




The BSA Meteor  I picked up for a small price was coated in loads of black paint, wouldn't fire a pellet as you could hear piston creep down the action , no breach seal, and no rear sight, and because its a mk111 its impossible to fit a scope mount at this time. A good stripdown, replacing the disintegrated leather spacer on the piston and turning a new breach seal (the O ring seemed fine), turps, wet and dry, and wirewool soon got the piston bore all smooth and shiny. Stripped the piant off the gun and got it looking spiffing and shooting fine, most definitely a project for more affluent times, I save a lot of money making my own parts.





Now the project I think deserves the most attention for now is the sad tale of the 22 Relum Telly I found in a skip many moons ago. The poor thing just lay there with a shattered stock and a slightly bent barrel a sure sign that the barrel had snapped shut prematurely. I plan to build a new stock for it - I have some lovely wood for this project and am quite eager to be getting on with it as soon as i'm over this stinking flu.

  

Friday, 23 November 2012

SO WHAT IS 'THE ANGRY, ANGRY GUN COMPANY'?

   The name came about from a suggestion made by my wife a short while back, and to tell you the truth I found it ironically amusing, so there it stayed. Airguns are a passion of mine as they are to many others young and old, whether they're used for plinking, hunting, field target, or HFT, even those who take it to the discipline of Olympic level.

I have several projects sitting around and I am keen to be getting on with them. I will document thier progress as well as the progess on tools and machinery such as gingery slyle lathe and metal smelting furnace to help me do a more professional job upon them. More than anything this will be a learning experience for me, and through  trial and error will be able to help others along the way, and hopefully learn from others myself. I have found you tube and google in general a great wealth of information.

One the major reasons for this blog is to find likeminded people in Cirencester  and surrounding area who are at a loss for somewhere to practice for HFT and FT without having to pay through the nose for the privilege.

So there will be documented projects to follow and possible recipes on pigeon pie, yum yum.

TTFN, Tet